How To Replace A Toilet Flapper – A useful Detailed Guide

 

Have you ever woken up in the middle of the night due to the noise of running water, and then figured out that its nothing but just your toilet filling? Most probably there is a problem with your toilet flapper. The flapper is the elastic portable seal located at the base of the tank of your toilet. It is the fitting that falls against the channel gap on the base of the tank and holds water in until whenever you flush. At the point when flappers wear out, water streams out, making the water valve open to top off the tank. Hence, we should repair our flapper with time, as it tends to lose its seal. 

A running latrine isn’t only a minor disturbance, all that wasted water flowing down the channel should be your well-deserved cash. That is the reason it’s so critical to replace the flapper when it starts to collapse. If you are able to call in a plumber to do the work for you, then that is great! If not, this article helps you replace your toilet flapper in just 6 easy steps. Every time you hear your toilet topping off over and over again, or in the event that you hear the consistent murmur of running water, your flapper might be spilling. The way to fix a running toilet is very straightforward and effortless. 

In order to replace their toilet flapper, one needs to understand the basic mechanism of how the toilet flapper works and how should we know when to replace it. The flappers in the toilet have a tendency to solidify, which keeps them from making a seal and holding back the water after flushing. A toilet that is running continually is an indication of an exhausted flapper. One of the easiest ways to test your toilet flapper is to add a few drops of dye in the tank. Try not to flush the toilet for at least an hour. If the water matches the color of your dye, then you need to replace your toilet flapper immediately, or you need to call a plumber to carry out the responsibility for you.

The following steps can help you replace your toilet flapper in just a few minutes. All you need is a new flapper for replacement, a food coloring dye, and some patience. 

First Step :

It shouldn’t take you long to discover the flapper, as it is just at the base of your toilet water tank. Lift up the lid of the toilet and place it on an even surface. Mix a couple of drops of food coloring to the water when the tank is full, to observe any changes in the flapper. There is a possibility that the flapper might start leaking, which will indicate its emergency to be replaced. There shall be a change in the color of the water depending on whether the flapper is leaking or not.  In the event that the flapper is leaking, the water will be the same shade as the color of the dye. if the flapper is fine, then there shall be no change in the color of the water.

Second Step :

Turn off the water in the toilet, by stopping the key valve. Generally, the valve for the toilet water is situated below the tank on the left or right side.

Third Step :

Flush the toilet to purge out the excess water which remains in the tank. If needed, then hold the flush handle down until nearly all of the water is out of the tank.

Fourth Step :

The flapper connects to two sections on the valve of the flush. Cautiously expel the flapper from the valve by somewhat turning each side, and separate the chain to eliminate the old flapper.

Fifth Step :

Add a new flapper. In order to replace your old flapper with a new one, cautiously attach the new flapper to the valve of the flush and then, attach the chain once again.

Disengage the chain of the flapper from the handle switch of the toilet’s flush. This switch is a level bar that runs from the flush handle to a position simply over the flapper. There is typically a little clasp on the top finish of the chain that guides into one of the gaps on the handle switch. Fix the clasp and let the chain drop; you will get rid of this chain as you introduce the new flapper.

Try to slide the side ears of the flapper away from the pegs, which are stretching out from the sides of the flush valve tube. On flappers made of hard plastic, these ears will snap free; but on flappers made of delicate elastic, the ears basically glide off the pegs.

Sixth Step :

Finally, repeat the dye test once again to ensure that you have accurately replaced your toilet flapper. So, turn on the water in your toilet, and flush your toilet multiple times. Then add a few drops of the same food coloring dye and wait for an hour to see the change in the color of the water. If the water does not change its color, then well done!

Does your toilet flush run all the time? Can you hear a leak throughout the day? Your toilet flapper may have just come to its end of life. You may not really think about your flapper, as it is just a small round object at the base of your tank. However, this little segment is important for your toilet to work the manner in which it should. Having a basic knowledge of when and how to replace your flapper, which you should have after reading this article, will help you to stay away from leakage in your toilet. This will also help you keep your peace of mind, as a leaky toilet flush can be far more agitating than we assume it to be. 

Leave a Comment